TL;DR
- A handyman invoice that gets paid on site gives each task a header with its own labor and parts lines, then a trip charge, the deposit as a credit and one BALANCE DUE.
- Our sample three-task visit in Minneapolis bills $352.95, and the balance after a $115.70 deposit is $237.25.
- The $81 hourly rate starts at the BLS median maintenance wage of $23.84, then adds benefits, unbilled time, overhead and profit.
- The Excel workbook and print-ready PDF are free, and the full sample is in a table below.
- Take ACH when you can. On the sample balance, ACH costs $1.90 to $2.37 and cards $5.93 to $8.30.
- In Minnesota, two or more trades for a homeowner needs a remodeler license, unless yearly receipts stay under $15,000 with a Certificate of Exemption.
A handyman invoice template that gets paid on the spot breaks the visit into tasks, bills each task's labor and parts on separate lines, adds the trip charge and subtracts the deposit. On our sample Minneapolis visit, that leaves a balance due of $237.25, collected before the truck leaves.
This guide is for the solo handyman and for the office manager at a two-to-five-person home repair company. Every figure in it was read at its source on November 21, 2026.
Download this handyman invoice template. The editable Excel workbook with the totals wired up, a field guide tab, and a print-ready PDF are free in the contractor templates pack, alongside the other trades.
The handyman invoice template, filled in: one visit, three tasks
The sample is a fictional company, Bur Oak Handyman Co., billing a fictional homeowner in south Minneapolis. The customer approved three tasks in writing and paid a deposit at booking to cover the parts.
Here is every line, with the same quantities, rates and totals as the workbook.
| Description | Qty | Unit | Rate | Amount |
|---|---|---|---|---|
| Task 1: Hallway walls, five drywall patches | ||||
| Labor: patch, sand and texture five holes | 0.75 | hr | $81.00 | $60.75 |
| Materials: compound, mesh tape, texture, primer (cost $40 + 30%) | 1 | lot | $52.00 | $52.00 |
| Task 2: Bedroom door sticks and will not latch | ||||
| Labor: plane door edge, reset strike plate, swap knob | 1.25 | hr | $81.00 | $101.25 |
| Interior passage knob (cost $10 + 30%) | 1 | each | $13.00 | $13.00 |
| Task 3: Back entry door lets in a draft | ||||
| Labor: fit and install a new door sweep | 0.25 | hr | $81.00 | $20.25 |
| Door sweep (cost $13 a foot + 30%) | 3 | ft | $16.90 | $50.70 |
| Trip charge | ||||
| Trip charge, Minneapolis service area | 1 | each | $55.00 | $55.00 |
| Subtotal | $352.95 | |||
| Sales tax (0%) | $0.00 | |||
| Less deposit paid at booking (2026-11-14) | $115.70 | |||
| BALANCE DUE | $237.25 | |||
Each task gets a header in the customer's own words, then its labor line, then its parts line. The customer reads down the page and checks each repair against what they asked for, which is the job a multi-task invoice has to do.
Labor is a little over half the subtotal. Parts are about a third, and the trip charge is the rest.
Walk the handyman invoice template top to bottom
The ranking template pages hand over a blank grid. Wave's handyman page names no rate or markup. Jobber's says to show markup on its own line or build it into the unit cost, and to give trip fees their own line, with no amount for either. Here is what goes in each section, in the order it prints.
Identity and license line
Business name, phone, email, insurance and the license or registration line. Which line you print depends on your state and on how many trades the visit touched.
In Minnesota the sample prints a residential remodeler license number. Drywall patching falls under the drywall and plaster skill and door work under carpentry. The Department of Labor and Industry requires a license from anyone offering two or more of those skills to a homeowner. The licensing section below covers the exemption.
Invoice number and dates
Use a sequential number and print the service date apart from the invoice date. When the invoice is handed over at the door, the two dates match and the customer has nothing to wait for.
Bill to and service address
Print both, even when they match. Landlords, property managers and adult children paying for a parent's repairs pay from somewhere else. The sample adds an access note: side door, lockbox code on file.
Visit summary
This is the handyman block, and the one blank templates leave out. It records time on site, the approved work order, how the visit is priced and anything found but not fixed.
The sample notes a rattling bathroom fan, quoted separately, with any wiring sent to a licensed electrician. That line is a future job and a written record that you flagged the problem.
Task headers and labor lines
One header per task, then hours at your rate in quarter hours. The sample bills 0.75 hours for five drywall patches, the labor time in Thumbtack's drywall repair guide for the same five patches.
The door hours are a placeholder. We found no published time for planing a sticking door, so time your own.
Materials at cost plus a markup
List each part at your cost plus a stated markup. Housecall Pro's handyman pricing guide prints 10% to 30% and uses 30% in its own worked example, so the sample does too.
The sample's part costs come from published guides. The $40 of patch materials is Thumbtack's figure. Fixr supplies the $10 basic knob and the $13 a foot for a door sweep, the low end of its range.
Trip charge
Put the drive on its own line. Housecall Pro prints trip fees of $30 to $80, and the sample charges $55, the middle of that range.
The same guide prints minimum service fees of $125 to $200, sized to cover up to an hour of labor plus travel. The sample skips the minimum because its labor runs past an hour.
Sales tax
The sample's tax rate is 0%. Minnesota's Department of Revenue tells contractors not to charge sales tax on construction contracts and to pay tax on materials when they buy them.
Its contractor guide treats repair work on real property as improving it, and says to pass the tax you paid through in the materials price. Items that are not built into the house are taxable retail sales. Other states draw the line elsewhere, so check yours.
Deposit and BALANCE DUE
The $115.70 deposit paid for the parts at booking, so it shows as a credit with its date. That is 33% of the job, inside the 30% to 50% Housecall Pro suggests collecting up front to cover materials.
BALANCE DUE is the one number the customer pays today: $352.95 less $115.70, or $237.25.
Terms, warranty and how to pay
Payment due on completion, any late charge agreed in writing, a workmanship warranty and every way to pay. The sample promises one year on workmanship. That is our sample term, so print your own.
Where the $81 an hour on the invoice comes from
The Bureau of Labor Statistics (BLS) has no handyman category. The closest is general maintenance and repair workers, whose work BLS describes as tasks that do not need a licensed tradesperson's training. Here is how their median wage becomes the rate on the invoice.
| Step | Figure | Source |
|---|---|---|
| Median wage, maintenance and repair workers | $23.84 an hour | BLS, May 2025 |
| Times 1.458 for benefits and taxes | $34.76 | BLS employer costs, June 2026 |
| Divided by a 65% billable share | $53.47 | Field Promax, 300 HVAC companies |
| Divided by 0.66 for overhead and profit | $81.02 | NAHB overhead, 10% profit goal |
| Rate on the invoice | $81.00 an hour | |
The 1.458 comes from the BLS private-industry row for installation, maintenance and repair occupations: $49.01 of total compensation an hour on $33.61 of wages.
The billable share is the part of a paid hour a customer pays for. The only measured figure we found is HVAC: Field Promax counted 5.7 billable hours in an 8.8-hour paid day across 300 companies, as ACHR News reported in June.
Overhead takes 24% of the price, rounded from the 23.6% of revenue that remodelers in the National Association of Home Builders (NAHB) study spent on operating costs in fiscal 2024. NAHB counts the owner's pay inside that figure.
Profit is a 10% goal. The same NAHB study's remodelers averaged 6.3% net.
Our handyman hourly rate guide anchored its range on Thumbtack's hourly figure. Thumbtack's cost page, updated in November, now prints $134 to $460 a job and no hourly rate at all.
Housecall Pro's data puts Minneapolis handymen at $50 to $85 an hour, so $81 sits near the top of the local range. Set your own wage and costs in the calculator below.
The presets swap in other BLS medians. A carpenter's $29.12 wage, run the same way, prices at $98.97 an hour.
Price the visit before you invoice it
Rate times hours covers the labor lines. The other half of the check is whether the whole visit, parts included, carries its share of overhead and profit before the invoice prints.
The rule fits on a sticky note. Price equals direct cost divided by one minus overhead and profit. At 24% and 10% the divisor is 0.66.
- Labor cost. 2.25 hours at $53.50 a billable hour (the $53.47 above, rounded) is $120.38.
- Parts cost. $40 of patch materials, a $10 knob and $39 of door sweep make $89.
- Direct cost. Labor plus parts is $209.38.
- Price. $209.38 divided by 0.66 is $317.23. Overhead takes $76.14 of it and $31.72 is profit.
Set your own numbers in the calculator below. Its default is the sample visit, and the other buttons load single tasks with times and part costs from Thumbtack, TaskRabbit, Fixr and Housecall Pro.
The calculator lands at $317, about $36 under the invoice subtotal.
The gap comes from two lines: the invoice adds the $55 trip charge, and it marks parts up 30% where dividing by 0.66 would mark them up 52%.
So the trip charge is doing real work. Drop it and keep the 30% parts markup, and the visit bills less than its costs call for.
Why adding 34% to cost loses money
The common slip is to add overhead and profit to cost as one 34% markup. On the sample that quotes $280.56. Overhead takes $67.33 of it, which leaves $3.85 of profit on a job done well.
Markup is a share of cost, while overhead and profit are shares of the price. Dividing handles that. Our markup vs margin guide has the full conversion table.
Invoices priced right, but the calendar has holes?
Skill Mammoth builds websites and runs marketing for contractors and home service businesses. Start with an audit of the site that should be booking your visits.
Hourly or per task: bill so the customer can check it
Hourly lines suit work you cannot see until you open it up. Flat per-task prices suit jobs you have timed many times. Here is each sample task beside the figures the guides print.
| Task | Sample invoice | Published figure |
|---|---|---|
| Five drywall patches | $112.75 | $200 for the same five, Thumbtack example |
| Drywall patching, up to 4 by 4 feet | Not on the sample | $337 to $863, Housecall Pro |
| Sticking door, planed, new knob | $114.25 | $75 to $225 interior door repair, Housecall Pro |
| Door sweep on one door | $70.95 | $35 to $90 a door, Fixr |
Every sample task sits inside or under the published figures. Thumbtack's example charges $200 for the same 45 minutes and $40 of materials.
A flat $200 for those five patches would beat the hourly bill by $87.25. That is the case for flat pricing on work you have timed: speed becomes your profit instead of a smaller invoice.
Keep hourly for the unknowns, and write any add-on found mid-visit as a change order before you do it. Our handyman contract template carries the deposit, change-order and late-charge language this invoice refers back to.
When a handyman needs a contractor license
The license line on the invoice depends on the state, the dollar value and the trades involved. Here is what each state page we read prints.
| State | When a license is needed | Dollar threshold printed |
|---|---|---|
| Minnesota | Two or more special skills for a homeowner | Exempt under $15,000 a year, with a certificate |
| Minnesota | One special skill only | No state license, except roofing |
| California | Bids over $1,000, permit work or any employee | $1,000 since January 1, 2025 |
| Florida | Any electrical work, drinking water lines, central air, roofs | None printed |
Minnesota's exemption counts gross receipts, not profit. Go over $15,000 in a calendar year and statute 326B.805 says to surrender the certificate at once and apply for the license.
Minnesota's special skills are listed in statute. Carpentry covers doors and decks, and drywall and plaster covers taping, finishing and painting. A visit that patches a wall and planes a door has used two.
California raised its limit through Assembly Bill 2622. An unlicensed handyman who advertises must say in the ad that they are not licensed, and the exemption does not cover anyone who advertises as licensed.
Florida's Department of Business and Professional Regulation says paying someone for even the simplest electrical work, such as connecting two wires, requires a licensee. The same page lists load-bearing wall changes and potable water plumbing.
Our guide to how to start a handyman business covers registration and insurance alongside the license question.
Payment terms and late charges your state allows
The sample makes the balance due on completion, the simplest term for homeowner work. Jobber's handyman template page advises payment within two weeks and terms no longer than net 30.
A late charge has to be agreed before the work, in writing, and it has to fit state law. Minnesota's general interest statute, section 334.01, sets 6% a year when no rate was agreed in writing. A written agreement can set up to 8% a year on debts under $100,000.
The sample prints 8% simple interest after 30 days, agreed on the signed work order. Other Minnesota laws cover particular kinds of credit, so have an attorney read your terms before you print a flat late fee.
Deposits have their own rules. California's Contractors State License Board (CSLB) says a home improvement down payment should never exceed 10% of the contract price or $1,000, whichever is less. It requires a written contract for jobs over $500.
At 33%, the sample's deposit would break that cap on a California home improvement contract. The Minnesota pages we read set no deposit figure for handyman work.
Get paid before you leave the driveway
The fastest invoice is the one paid at the door. Here is what each processor's own pricing page printed today, and what each would take from the sample's $237.25 balance.
| Processor and method | Printed rate | Fee on $237.25 |
|---|---|---|
| QuickBooks Payments, swiped card | 2.5% | $5.93 |
| Square Free, tap, dip or swipe | 2.6% + 15¢ | $6.32 |
| Stripe Terminal, in person | 2.7% + 5¢ | $6.46 |
| Jobber Payments, Tap to Pay | 2.7% + 30¢ | $6.71 |
| QuickBooks Payments, invoiced card | 2.99% | $7.09 |
| Stripe or Jobber, online card | 2.9% + 30¢ | $7.18 |
| Square Free, online card | 3.3% + 30¢ | $8.13 |
| QuickBooks Payments, keyed card | 3.5% | $8.30 |
| Stripe ACH Direct Debit | 0.8%, $5 cap | $1.90 |
| Square, QuickBooks or Jobber ACH | 1% | $2.37 |
| Cheapest on this balance | Stripe ACH, $1.90 | |
On this balance the card fees run $5.93 to $8.30, and ACH costs $1.90 to $2.37. The gap widens with the ticket.
On the $2,464 deck repair in Housecall Pro's worked example, an online card payment at Stripe's rate costs $71.76. Stripe's ACH cap holds the same payment to $5.
Square's ACH page prints 1% with a $1 minimum. Its pricing page lists a $10 ACH cap on the Plus plan.
Hand over a card reader at the end of the visit, and put the ACH link on the emailed copy for anyone who would rather pay from the bank.
What the invoicing apps print for price
Once a spreadsheet gets slow, the software that sends the invoice and takes the payment prints its price. Free tiers exist. Zoho Invoice lists $0 with up to 500 invoices a year. Wave and Square list $0 plans, and QuickBooks Free allows 2 invoices a month.
Drag the budget in the tool below to see which paid plans fit.
Our handyman software comparison covers scheduling and quoting as well as invoicing.
Invoice, estimate or receipt: one short answer
- Estimate: the price you propose before the work. It can change once you open the wall.
- Invoice: the bill after the work, with the deposit credited and a balance due.
- Receipt: proof of payment. Mark the invoice paid, with the date and method, and it becomes one.
- Bill: another word for an invoice. Google counts "handyman bill template" searches with the invoice template ones.
Keep all three under one job number, so the estimate, the invoice and the paid receipt line up when a customer calls a year later.
Owners look for a better invoice in spring
We pulled 12 months of US Google search data for 15 handyman invoice and pricing searches on November 21, 2026. Google groups "handyman invoice template", "handyman bill template" and the Word version into one count.
| Search | US searches a month | Click price | Busiest months |
|---|---|---|---|
| handyman invoice template (grouped) | 480 | $4.63 | Feb to Apr, 590 |
| handyman invoice | 210 | $15.06 | Jan, Mar to May, 260 |
| free handyman invoice template | 140 | $8.34 | Mar to May, 170 |
| handyman estimate template | 110 | $9.56 | Mar and Apr, 170 |
| handyman receipt template | 70 | $5.54 | Dec, Mar and Jul, 90 |
| home repair invoice template | 50 | $5.73 | Mar, 90 |
| handyman rates | 1,600 | $4.72 | Nov and Dec, 2,900 |
The template group ran 590 searches a month from February through April and 390 from July through October, a 51% lift in spring. We computed that from Google's monthly counts for the grouped search over the 12 months we pulled.
Rate searches move the other way. "Handyman rates" hit 2,900 in November and December 2025, more than three times its summer months at 880.
Advertisers pay $15.06 a click for the bare phrase "handyman invoice", about three times the $4.63 for the template search. The ranking template pages show none of this. Fix the invoice and the rate before February, when the template searches start to climb.
Six mistakes that delay payment
- One lump-sum line. "Handyman services, $353" invites a dispute. Task headers with their own labor and parts lines answer it.
- A hidden trip charge. Folded into labor, it makes your rate look high. On its own line it reads as the drive it is.
- Parts at cost. With no markup, the run to the store is free work. Housecall Pro prints 10% to 30%.
- A late charge nobody agreed to. Printed only on the invoice, it is a surprise. Put it on the signed work order first.
- No deposit credit. Leave the deposit off and the balance looks wrong, and the customer has to do the arithmetic.
- Mailing it next week. An invoice handed over at the door, with a card reader and an ACH link, gets paid while the customer is looking at the repaired wall.
Who published each figure, and when
| Publisher | What it gave this guide | Date |
|---|---|---|
| Bureau of Labor Statistics | Maintenance, carpenter, painter and drywall wages | May 2025 survey |
| Bureau of Labor Statistics | Employer benefit and tax cost per wage dollar | June 2026 |
| Field Promax, via ACHR News | 65% billable share across 300 HVAC companies | June 16, 2026 |
| NAHB | Remodeler overhead 23.6%, net 6.3%, fiscal 2024 | April 8, 2026 |
| Housecall Pro | 23,963 handyman entries: rates, markup, trip fees, deposits | November 19, 2026 |
| Thumbtack | Per-job range and the five-patch drywall example | November 2 and April 9, 2026 |
| Fixr | Knob, door sweep, faucet and TV mount figures | January and February 2025 |
| TaskRabbit | TV mounting time and mount prices | November 17, 2026 |
| Minnesota DLI and statutes | License rules, special skills, interest rates | Read November 21, 2026 |
| Minnesota Department of Revenue | Sales tax on contractor work | Pages dated 2021 to 2025 |
| CSLB | $1,000 handyman limit and deposit cap | Bulletin of December 31, 2024 |
| Florida DBPR | Work that needs a licensee | Read November 21, 2026 |
| Processor and app pricing pages | Card, ACH and plan prices | Read November 21, 2026 |
| DataForSEO | Google search counts and click prices | Pulled November 21, 2026 |
When the invoices are right and the phone is quiet
A clean invoice collects on the jobs you already have, and it does nothing to bring in the next one.
Skill Mammoth builds websites and runs marketing for contractors and home service businesses. Plans start at $350 a month, and a website build is $3,000 or $150 a month for 24 months. If your invoices get paid and the calendar still has gaps, that is the part we can help with.
The handyman invoice workbook and PDF are free in the contractor templates pack. For larger jobs, the general contractor invoice template uses the same layout.
Want more visits to invoice?
We build the website and run the marketing that fills a handyman schedule. Plans start at $350 a month.
Frequently asked questions
What should a handyman invoice include?
Your business name, contact details and license or registration line, a sequential invoice number with the service date, the bill-to and service addresses, and a short visit summary. Then one header per task with its own labor and parts lines, a trip charge line, sales tax where it applies, the deposit as a credit and one balance due. Close with payment terms, any agreed late charge, your warranty and how to pay.
How do you price a handyman invoice?
Build an hourly rate from your costs, then check the whole visit. The sample starts at the BLS median maintenance wage of $23.84, adds benefits and taxes, divides by a 65% billable share, then divides by 0.66 to leave 24% for overhead and 10% for profit. That gives $81 an hour. Parts go on at cost plus 30%, and the trip charge gets its own line.
Should a handyman charge a trip fee?
Many charge for the drive, either as a trip fee or as a minimum, though Fixr notes that not all do. Housecall Pro's handyman pricing guide prints trip fees of $30 to $80 and minimum service fees of $125 to $200. On our sample, the $55 trip charge is what lifts the invoice above the price its costs call for, because the parts carry a smaller markup.
Can a handyman charge a late fee?
Only if the customer agreed to it in writing before the work, and only inside your state's limits. In Minnesota, statute 334.01 sets 6% a year when no rate was agreed in writing and lets a written agreement set up to 8% a year on debts under $100,000. The sample prints 8% simple interest after 30 days. Have an attorney check your terms.
Does a handyman need a contractor license?
It depends on the state. Minnesota requires a residential remodeler or building contractor license for two or more special skills, unless yearly receipts stay under $15,000 with a Certificate of Exemption. California allows unlicensed work only on bids up to $1,000 with no permit and no employees. Florida requires a licensee for any paid electrical work, even connecting two wires.
What is the difference between a handyman invoice, estimate and receipt?
An estimate is the price you propose before the work, and it can change once you open a wall. The invoice is the bill after the work, with the deposit credited and a balance due. A receipt is proof of payment: mark the invoice paid, with the date and method, and it becomes one. Keep all three under the same job number.
ChatGPT